VIBE FM Mk1 Open firmware, officially supported. The first 100 get 10% off Join the list →

The Firmware Hub · FM-1 · Araminta

Araminta for the M-VAVE FM-1

Araminta4.8

by Wulgaren GitHub ↗

groovebox

Synthesizer firmware for the M-VAVE FM-1. A Felucca 1.5.1 fork with free take, punch-ins, DRUM-X, 13 engines, and a chainable effects list.

Text by the maker.

About it

Runs on
FM-1 · Browser ↗
Release
4.8 · released 20 Nov 2026 · on the hub since 22 Nov 2026596 KB · what's new
Licence
GPL-3.0 · source ↗ · copy on the hub
Flash chip
Every FM-1, the newer chip 0xB36014 too
Identity
FM-1_4248what it reports over USB while it runs
Build
Built by its maker, not signed
Popular
★ 15 on GitHub

Like Araminta

Changelog

What changed, version by version19 versions

4.8

More of the audio path runs from RAM, punch-in keeps its place when the song clock moves, and the editor matches the panel's ENV DEST cards.

Splash and ABOUT show v4.8.

  • RAMTEXT grows and the hottest flash code moves into .hot_text. The linker room for RAM code is 0x8600, the flash hot block is ordered so its lines stop sharing cache sets, and more of the render runs from RAM: SINE / ENV_EXP / TANH_Q15, fm6_core_render, drum_bus, mix_part / track_render_audio, then perf_begin, duck_block and bus_c1. On the PHYS sweep stores (JieLi, device-timed emulator) busy_phys goes from 68.0 to 66.0 % CPU with misses/half 275.5 to 184.7, psy_phys from 74.6 to 72.3 % with late halves 4 to 2, and psy_stack from 78.9 to 76.2 % with voices shed 15 to 3.
  • PHYS modal coefficients stay while their inputs hold. px_modal_block no longer rebuilds every mode's set each block when f0, STRC, BRIT, DAMP, ACC and POS are unchanged. Bit-exact when the inputs hold; device timed, the modal share of core 0 roughly halves on busy PHYS and PSYCHODELIA.
  • PHASER / FLANGER / CHORUS inserts cost less. Their delay lines update once a block instead of every sample. Sound unchanged for the checked paths.
  • Open-toolchain Mac builds gate on a 1.08 JieLi size estimate (was 1.12). Measured open 31,616 B to JieLi 33,936 B (x1.073) on this tree; the old factor false-failed native builds that still fit under JieLi/CI.
  • The lane keeps its step when the song clock moves. TAPE MASTER with TEMPO OFF (and a SPEED driven from the mod matrix) retimes the 1/16; the lane index is rescaled with it, so a held punch-in no longer restarts every block. On PSYCHODELIA with K3 MASTER that was the crackle: about 75 % of a half and no late halves where it had been over 100 % with hundreds of late halves.
  • Transport changes apply before lane MIDI effects, and the emulator can hold a project's punch-in (or a page-1 stack) over its own patch for load checks.
  • TAPE DROP no longer crackles on a busy bar. The overload was a bad core split at note-on, not the tape head: a still head skips the moving-head path, and a part that just started a voice weighs its recent peak when splitting. mix_part and track_render_audio run from RAM.
  • A vel or chance write keeps RATCH on the step (byte writes no longer clear it).
  • PHYS modal state no longer drops its coefficients while the note's modal inputs hold (see CPU).
  • ENV DEST cards follow LFO DEST (PIT FLT SHP, then SYNC) on the device and in the web editor.
  • Grouped pages for the 127-parameter layout in the web editor.
  • Session recorder for the emulator (?rec=1).
  • PHYS sweep stores (tests/emu/phys/): busy_phys, psy_phys and psy_stack_p1_lfo, plus tools/phys_sweep.sh, for the device-timed emulator cases the RAM-layout work was measured with.

4.7

The delay and the HALL reverb cost less CPU, a silent one skips its block, and a delay tail dies out to silence.

Splash and ABOUT show v4.7.

  • The delay and the HALL reverb run from RAM. dly_process_late and rev_hall moved into .hot_text, so core 1 no longer fetches them through the 32 KB flash cache every block. In the emulator (median of 8 flash layouts) the busy project drops from 66.8 to 62.1 % on core 0 and 37.5 to 34.0 % on core 1, and the stack scenario from 86.3 to 82.0 % with 6 late halves instead of 32. The sound is bit for bit the same.
  • A silent HALL reverb skips its block. Once the HALL's input has been zero for 128 blocks and a scan finds every line, filter and all-pass at zero, rev_hall only moves the tap drift (and the gains after a SIZE change) until input comes back. Idle drops from 18.0 to 14.8 % on core 0 and 7.0 to 3.1 % on core 1, and playback gains about a point (busy 62.1 to 61.1 %, stack 82.0 to 81.2 %). tests/gate_test.c checks the output against an ungated build bit for bit, and that the gate engages after notes and after a SIZE change.
  • A silent delay skips its block. Once the delay has had zero input and written only zeros for a full line (1.49 s), its low-pass is 0 and its tap is still, dly_process_late only moves the write head until input comes back. Idle on core 1 drops from 3.1 to 1.2 % (open toolchain, median of 8 flash layouts); core 0 and playback stay the same. tests/gate_test.c checks the output against an ungated build bit for bit, and tests/dly_decay_test.c that the gate engages at any FDBK and COLR.
  • The delay's tail dies out to silence. The delay's low-pass now keeps its rounding remainder and its feedback rounds towards zero. Before, after any note with FDBK above 0, the feedback loop held an offset of up to 6 steps for ever, so the delay was never silent again. Repeats differ by at most 17 steps of 32,768, 59 to 67 dB under the music, and 111 of the 139 golden renders and the engine-switch hashes were rewritten for it. tests/dly_decay_test.c checks that a burst decays to exact zeros at any FDBK and COLR.
  • CPU reports for the emulator. emu_test --scenario idle measures the power-on project with nothing playing, tests/emu/busy_project.bin is a 4-track project with every send, inserts, a MASTER insert and the SLICER, and each run prints flash cache misses a half and each part's render time. tools/cpu_report.py prints the load and size tables a CPU change needs, and tests/emu/clickcheck.py compares two renders sample by sample. No firmware change.

4.6

A drum kit's keybed is its eight pads, DRUM-X gains a HOUSE kit, SAVE loses its phrase loader, and OTT costs less.

Splash and ABOUT show v4.6.

  • The keybed is the kit. DRUM-X and a SAMPLE drum kit (CR78, a USR drum kit) play KICK, SNARE, CLAP, HAT CL, HAT OP, TOM, RIM and BELL on the first eight white keys (F G A B C D E F); every other key plays nothing. The octave buttons no longer move a kit: F is the kick at any OCT (the other tracks still follow them). GM notes from MIDI and from older patterns play the same lanes as before.
  • The eight pads glow. A kit track's pages light the eight keys at the mid level, and a hit lights its key, so the kit can be found without playing it.
  • A, MRPH or B from the keys. On a DRUM-X track's EDIT pages (EDIT 1, EDIT 2, SOUND, TONE, MOVEMENT), F# auditions the A patch, G# the kit's MRPH as stored and A# the B patch, and the panel's A---B bar moves to what plays. The three keys glow, the one playing lit. On SOUND, TONE and MOVEMENT, F# and A# also pick the patch the cards edit, and a side picked with the LANE knob is auditioned too. Turning MRPH or leaving the pages puts the kit back on its MRPH, and nothing is stored with the project.
  • SAMPLE kits act as kits. A CR78 or USR kit's notes no longer take PITCH, TRN, the chord settings or the scale LEDs, as DRUM-X's never did.
  • HOUSE, an 18th factory kit after the TR-707: a short clicky kick (about 58 Hz, DRIVE), a bright tight snare, a short clap, very short closed hats and a shorter open hat, a tuned tom, a dry rimshot and a cowbell. TONE 90, DECY 58, NOIS 70, DRV 28, a small reverb send. As the other kits since 4.1, every lane plays at its LEVEL 127: the kit's own balance carries the mix. The 707's tambourine, crash and ride have no lane in DRUM-X's eight.
  • SAVE > PHRASES is gone. The 13 factory phrases, the page, the per-preset phrase hint and the phrase stored in a user preset are removed. The sound dice and the punch-in lane stay.
  • SAVE is PRESETS, USER, PROJECT, then CLEAR. PROJECT is the third page of the sounds section instead of a section of its own.
  • Compatibility. A user preset record keeps its 32 phrase bytes as reserved: the bank size, record size and versions are unchanged, UP_GET sends zeros there and UP_PUT ignores what it sends. Older firmware still reads the banks and shows no phrase for a new record. Projects, settings and samples are untouched.
  • The firmware image shrinks by about 3 KB.
  • ALL SEQUENCES CLEARED replaces the old "ALL PATTERNS CLEARED" message, as the CLEAR key has said "CLEAR ALL SEQUENCES?" for a while.
  • Slicer MIX starts at 0. A new track's SLCR MIX is bypass, as every insert's MIX is; raising the mode alone stays silent until the MIX is raised. Projects and presets keep their stored values.
  • OTT at DEPTH 0 is the insert off. DRIVE 0 used to run the full LR4 crossover for its allpass sum. It now passes the dry signal and skips the six filters, so raising DEPTH re-arms a clean crossover.
  • OTT costs less. The six integrator sections drop their per-sample int64 clamps, which cannot fire with the section's bounded inputs, and their products use the positive coefficients as unsigned. ins_run_ott drops from 968 to 601 instructions (tests/target_budget.txt) and the image from 583,868 to 582,460 bytes.

4.5

The punch-in lane gets a page and undo, imported DX7 patches with AMS stop hissing, and a muted track ramps out.

Splash and ABOUT show v4.5.

  • A page of its own. PUNCH-IN 3/3 lists the lane as AUTOMATION's list: a row per effect per run of steps. KNOB 2 moves a run, KNOB 3 sets its length, KNOB 4 changes its effect. OCT- deletes the run; OCT+ asks CLEAR PUNCH LANE?.
  • SAVE held undoes a lane edit. One knob gesture is one undo, held again it redoes. A REC pass over the lane is one undo too.
  • G5 CLR while recording empties the lane steps it passes. With FX LATCH its press still turns the latched effects off.
  • CLEAR ALL AUTOMATION clears the lane as well. A single track's AUTOMATION clear leaves it to the lane page.
  • FM6 AMS levels. Operators with AMS no longer jump between silence and full scale. Imported DX7 voices that use AMS, such as SYN PAD 6, BALI GONG and TRAIN, lose the broadband noise. The regression test checks AMS 3 at AMD 0 and AMD 50.
  • MIXER and GLO mute. PLAY OFF now ramps out a note that is already sounding. Before, it only blocked new notes.
  • Effect graphs follow the page. With DIST, FILTER, CRUSH, PHASER or FLANGER on SEND or MASTER, the graph reads the shared bus values the cards edit, not the track's stale values.
  • Editor SysEx across OTA dispatch. An editor request arriving while an OTA frame is being dispatched is no longer dropped.
  • Official V16 installer. tools/fm1_install.py and the web installer accept the unmodified V16 stock file without --force.
  • The app slot grows into the package's 0xFF fill before 0x93000, keeping the last app sector's final 256 B blank. The image length and the OTA check are unchanged.

4.4

The render keeps its hot flash code in one fixed block, the punch-in layer runs on the second core, and overlapping punch-ins record on their own edges.

Splash and ABOUT show v4.4.

  • The render's hot flash code has a fixed home. Its 94 hottest functions (41,540 B) sit together after the boot code, 64-byte aligned, with the hot tables next, so an edit elsewhere no longer moves them between cache sets. Over 8 flash layouts, stack's median load fell from 94.5 % to 87.5 %, and its median late halves from 393.5 to 39.
  • The punch-in layer runs on the second core. The mix leaves one 0.73 ms block late, a constant delay: the click, the HOME scope and the USB tap see that block.
  • Overlapping punch-ins record on their own edges. With REC armed, two effects held at once no longer share one press state. A press in a step's second half starts at the next step, and a release in a step's first half ends at the previous one, without touching the other effect's steps.
  • SELECT on the punch-in and SEQ tools maps no longer drops a turn when the audio render preempts the main loop.

4.3

LFOs keep time with the tempo, the punch-in lane holds every effect a step had, and a project keeps all 255 automation records. Projects are FUN21.

Splash and ABOUT show v4.3.

  • Pages. LFO 1/3 is RATE WAVE TRIG SYNC (how fast, and when it starts); LFO 2/3 is PHS FADE POL SMTH (its shape; its header was LFO 2 2/3); LFO DEST is 3/3.
  • SYNC is ON / OFF. With SYNC on, RATE's knob turns note values (4BAR .. 1/32, longest first) instead of Hz, as ENV SYNC does for ATK DEC REL. RATE is one automation row and one lock, SYNC on or off, and the matrix's RATE moves the note value. RATE is no longer dimmed with SYNC on.
  • PHS is dimmed on TRIG FREE with SYNC off, the one case where nothing restarts the LFO at PHS (FREE + SYNC still starts it at PHS on PLAY).
  • The graph is a phrase over one bar of the tempo. RATE shows as the cycles in the bar (SYNC 1/4: four, at any tempo). TRIG NOTE starts it at PHS and the graph stands still; FREE starts it at the live phase and it scrolls. FADE ramps it in from the left edge, POL UNI draws 0..+1 over the bottom line, S&H's steps glide over SMTH.
  • Every punch-in records. With REC armed and the transport playing, REPEAT, LPF, HPF, REVERSE, TAPE STOP, FREEZE, PITCH UP / DN, FLANGER, PHASER, the THROWs and GLITCH now go into the punch-in lane as the MIDI ones did, and play back on the master. A recorded REPEAT or REVERSE starts on its step's 1/16. Before, only OCT±, DEC±, STUTTER, ATK+, ARP, RANDOM and /2 / \*2 were recorded.
  • Effects stack on a step. A step holds every effect held while it passed, not just one. Recording over a step adds to what it holds: REPEAT in one pass and LPF in the next both play. The lane keeps playing while you record.
  • 255 records, all saved. A project keeps every automation record and lock the device holds, now 255 (192 before; a save kept 148). AUTOMATION SAVE LIMIT and the SAVE warning that extra records won't be saved are gone.
  • SYNC's stored value is 0 / 1 now; RATE holds the note value while it is on. Projects mark this in header byte 67 bit 3; user presets in bit 1 of the VIB byte. A project or preset without the mark (all saved before) loads its SYNC note value as SYNC ON with RATE on that note value, so it plays the same. A synced part's RATE automation and locks, which did nothing, are dropped on load. Older firmware reads SYNC ON as 4BAR.
  • Projects are FUN21 (FUNL, 4864 B). FUN20's first 4080 bytes keep their places; the tail after them holds the punch-in lane (an effect mask per step) and automation records 149..255, then the name and the hash. FUN20 and older projects still load, a FUN20 lane as one effect a step. Firmware before 4.3 cannot open a FUN21: back up in the web editor before the first save if you need a copy it can read.
  • Backups: a project slot lists at the size of the record it holds (a slot saved by earlier firmware keeps its FUN20 or FUN19 size until saved over). The web editor accepts 4864 B projects; update it with the firmware.
  • Editor protocol: id 91 SYNC is OFF ON. Library files key it LSYNC; a file keyed SYNC (written before) converts as above when it loads.

4.2

The mod matrix has eight slots per track instead of four. KNOB 1 on the MOD page runs SLOT 1..8, and the page lists slots 1..4 or 5..8, whichever holds the one selected. The DRUM-X sound dice now starts from a random factory kit.

Splash and ABOUT show v4.2.

  • Slots 1..4 keep their parameter ids (49..60). Slots 5..8 have none: P_COUNT is full.
  • Projects stay FUN20. Slots 5..8 take the last 34 bytes before the name, so a project now saves 148 automation records instead of 155. AUTOMATION SAVE LIMIT fires on the 149th, and SAVE warns AUTOMATION WON'T SAVE past 148. A FUN20 file saved with 149..155 records still loads every record, with slots 5..8 off, and shows AUTOMATION SAVE LIMIT as it loads: a save or the autosave keeps 148 of them. Firmware 4.1 loads a project of now without slots 5..8.
  • User presets keep slots 5..8 in bytes the record never used, with no version change. Older presets load them off.
  • Editor protocol: MATRIX (cmd 103, INFO 58 01 8) reads and sets all eight slots and pushes device edits while WATCH is on. UP_GET / UP_PUT carry slots 5..8 after the category. The web editor lists SRC5..AMT8 after AMT4, and its patch files and user preset copies keep them.
  • DRUM-X: OCT+ held + PRESETS loads a random factory kit with its MODELs and LAYERs, then moves each sound's numbers by up to 40. One time in five a sound gets another WAVE, any of the four (was the first two). One time in eight it gets another MODEL. SAVE held undoes it. A kit another DRUM-X track shares stays as it is.
  • The SAMPLE sound dice no longer lands on the retired PERC preset, which switched the track to DRUM-X.

4.1

DRUM-X now runs JIANT's newer voice with 17 kits, and DRUMS folds into it. Lane levels move to the MIXER, and the SEQ and AUTOMATION pages get a simpler order.

Splash and ABOUT show v4.1.

  • Projects keep their size and layout (FUN20). Each sound's LAYER and MODEL ride in the kit bytes' spare top bits, and the filter GR in the mode byte: 3.10 and older refuse a project saved with any of them.
  • A DRUM-X project made before this plays the new voice. Its FM knob now strikes with the hit and decays with the pitch envelope, so a project with FM up sounds different.
  • DRUMS projects and user presets load as DRUM-X. A migrated project keeps its lane levels, zero and lowered ones included.
  • JIANT V10.7.24's DRUM-X voice replaces the older port: half-rate rendering, the V10.6q quality pass (cleaner noise, an 808 clap, a CMOS cowbell), the guiro filter GR, per-sound LAYER. FM now strikes with the hit and decays with the pitch envelope. DRV and the knee now run on the kit's sum.
  • 17 DRUM-X presets. The first is renamed FM DRUMS (same kit, same sound). JIANT's ten kits: 909 CLUB, 808 BOOM, LOFI DUST, INDUSTRIAL, ACOUSTIC, DUB ROOTS, TECHNO RAW, BREAKS, HIP HOP, LATIN PERC. Per-sound sends left out (JIANT ships them at 0), and so is JIANT's own DIST on five kits.
  • Each sound has a MODEL (EDIT > Kit > SOUND; LAYER on TONE): CLASSIC, or Felucca's DRUMS voices SHELL, METAL, TEETH, CLICK. Felucca's kits STD, 80, 10, 66, 55 and 77 are DRUM-X presets STD, 80, 10, 66, 55 and 77, translated from its numbers.
  • Kit pages read in percent, as the rest of the device reads its 0..127 values. TONE's third card is CHAR: what it offers changes with the MODEL (a drive, a drive and its short tail, a click ratio), so DRV was a misnomer. PTCH reads as its note and the cents above it, and the FM's second oscillator (OSC2) as its amount, 0 to 100 %. The layer itself has 16 positions.
  • DRUMS (engine 15) is retired. Projects and user presets on it load as DRUM-X with their KIT's kit (DEEP, TIGHT and PERC assembled from the others). Close to the old sound, not identical.
  • X-MOD playback removed (no page since 3.x).
  • Kit labels. EDIT's first section reads KIT 1/2 and KIT 2/2: both pages edit the whole kit now, so the old DRUMS HIT name is gone. TONE puts FILT first, then COLR / CUT / MIX. CHAR names the combined drive modes DR+BU and DR+SH.
  • Lane levels on the MIXER. A DRUM-X track's eight lane volumes moved from EDIT > LANES to the MIXER: SELECT walks MIXER 1/3 (the four tracks), 2/3 (KICK..HATCL) and 3/3 (HATOP..BELL), each lane with a live meter and its level in percent. The LANES section is gone. CR78 and USR drumkits have no lane levels and keep MIXER 1/3 alone.
  • SEQ pages. PATTERN is gone: its LEN / DIV / SWING / GATE knobs are on SEQ TOOLS and its layer. The step group walks STEP → DETAIL → AUTOMATION, and SEQ TOOLS → GENERATION → GENERATION 2 is the tools section (generation only on a drum kit). The tools map opens on SEQ TOOLS alone, so the generation pages keep their own knobs; its footer keeps the normal page layout, with OCT- UNDO where the sound name goes and the page count at the right. SEQ TOOLS' drum-lane mute reads MUT BD, not M BD.
  • QUANTIZE is the first row and the automation ON / OFF row (was PLAY) is second, now called ENABLED. A divider sits under the two settings. An empty list shows NO AUTOMATION above + ADD.
  • SAVE held now undoes a preset load that replaced the project's DRUM-X kit, and browsing presets keeps the kit change in the same undo step.
  • The firmware and host tests build with no warnings.

3.10

Projects grow to FUN20. The flash map takes more of the gap for autosave and banks. POLY gets chord glide. Factory sounds and FM6 patches land in the same build as DIST MODE OTT, with USB serial off so the image fits.

Splash and ABOUT show v3.10.

Projects are FUN20 (FUNK, 4096 B, one flash copy). FUN7..FUN19 still load. Autosave is a full 4096 B A/B pair (A at 0xE5000..0xE6FFF, B at 0x93000..0x94FFF). A pre-3.10 one-sector B at 0xE6000 migrates on boot. Settings keep their layout; row 13 stays reserved. Older 3840 B backups still restore.

Before installing over stock, take a full flash dump with tools/fm1_flash_dump.py. An editor SysEx backup does not keep factory radio calibration in the gap. The installer asks for that confirm when the device is not already running Araminta. Stock V15 erases the gap on every boot.

The 256 B append holds motion through record 155, plus a 40 B audio punch-in lane. AUTOMATION SAVE LIMIT fires on the 156th record (RAM still holds 192). A torn project save clears that slot; Save writes the current song into the autosave first so recovery is current. Punch-in borrow of sl_buf also drops MASTER STUT takes, so a master recording cannot read the punch loop.

User presets are 96 slots (six banks × 16). Banks 0/1 stay at 0xDC000. Banks 2..4 are single-copy at 0xF5000 / 0xF6000 / 0xF7000. Bank 5 uses 0x95000..0x96FFF. Backup ids 10..13 cover banks 2..5.

FM6 has four 32-voice homes: 0xE7000, 0xF8000, 0xF9000, and bank 3 at 0xF4000. SLOT is 0..143 (F1..F15, OWN, B1..B128). INFO advertises 128 bank voices as two 7-bit bytes. User-preset FM6 patches reclaim on delete and refuse a 33rd entry instead of saving a hollow preset.

EDIT > VOICE gains PIT GLD (POLY only). Chord notes pair with the next chord and glide, in the sequence or live from CHRD keys and MIDI. A released live chord keeps sounding for one 1/8 so the next can glide into it. A plucky envelope that has died attacks again at the new chord. With PIT GLD on, GLD reads as a share of the chord. Off by default. The switch is bit 5 of P_ALLOC (no format bump). Editor SWEEP SET keeps that bit. PITCH lives on VOICE 2 in every mode; UNISON keeps UNI DTN on VOICE. POLY SPRD automation records SPRD, not UNI DTN.

Seventeen new or reworked factory sounds join nine kept from the first pass (SYNC LEAD, SUB DRONE, TALK LEAD, RING NOISE, SYNC STACK, PERC STOP, GLASS BOW, and reworks of STRETCH, REG BELL, WT FDBK; NOISE LD leaves LOFI). FM6 adds F9..F15 (METAL VOX, HOLLOW FM, CRYSTAL, FM GROWL, OCT STACK, AIR NOISE, DUBSTEP BASS) and presets for them. DUBSTEP BASS lists under BASS.

DIST MODE OTT ships in the release image. USB serial (FELUCCA_CDC) defaults off so audio + MIDI fit; set FELUCCA_CDC=1 for a developer build with MENU > USB SERIAL.

MENU > SYSTEM > BOOT RESTORE (was RESTORE LAST). The autosave still writes on the idle rules when OFF; OFF only skips power-on restore.

Return to V15 and the install copy name Araminta's reclaim sectors (0xF4000..0xF9FFF and the gap user bank). Byte-exact stock needs the full flash dump above. UBOOT write-back of those sectors on return to V15 is not in this build.

EFFECTS > TAPE starts as MASTER at MIX 100 % (idle head at SPEED 100). SAVE > CLEAR's ALL keys also reset the mix and the arpeggiator. CC 71..74 turn the on-screen knobs; 75..77 are SELECT, ALGORITHM and PRESETS. MIDI LEARN is gone; its settings bytes stay reserved so older settings load.

3.9

A free take can record the arpeggiator. With the ARP on, the take holds the notes the arp plays, not the keys held. A latched ARP starts the take on its next note, the take keeps the tempo it played on, and closing it stops the arp so the sequence plays alone. The VOICE page puts PITCH last, so POLY, MONO and LEGATO show VCE GLD SPRD PITCH and the bend is K4.

Splash and ABOUT show v3.9.

No project, preset or setting change. Saves stay FUN19 (FUNJ) and 3.8 files load as they are.

With the ARP on, REC while stopped on an empty project records the notes the arp plays. A key starts a take, and a latched chord starts it on the ARP's next note, so HOLD works. The take keeps the tempo the ARP played on and ends at the nearest 1, 2 or 4 bars. Notes after the loop are dropped instead of wrapping onto step 1. Closing the take clears the latch and stops the ARP, so playback is only the recorded sequence.

PITCH is now the last card on VOICE. POLY, MONO and LEGATO show VCE GLD SPRD PITCH, so the bend is K4. UNISON keeps its four cards and PITCH on VOICE 2. The card behaves as in 3.8.

3.8

The VOICE page gains a pitch bend. UNISON gets it too, on a second page. CLOCK moves next to MASTER. Newer FM-1s with the UCUN flash can save and update again. The boot splash no longer pops, and there is a Control Surface for Live.

Splash and ABOUT show v3.8.

Projects and settings are unchanged. Saves stay FUN19 and 3.7 files load as they are.

In POLY, MONO and LEGATO, the empty card on the VOICE page is now PITCH. Turn it to bend the track. By default it reaches 2 semitones each way, the same range as MIDI pitch bend.

The bend stays where you leave it, and changing track recentres it. It is live, so it is not saved with the sound. An external pitch wheel moves the card too.

In UNISON the VOICE page keeps its four cards. Press SELECT to open VOICE 2 for PITCH, and SELECT again to go back.

CLOCK is now MASTER's second page. GLO opens MASTER, SELECT walks to CLOCK, and the next GLO press opens SONG.

LFO TRIG turns the other way. Left of NOTE is FREE, as DELAY's K4 steps left to TIME.

Dead engine cards no longer appear in MOD destinations, AUTOMATION rows or step locks.

SAVE > CLEAR keeps the keys silent while its confirmation is open.

CLEAR ALL4 puts MAP back to OFF with the rest of the track.

Newer FM-1s with the UCUN UC25HQ80 flash now save settings, projects and samples, and update from the running firmware. Both flash parts work. A unit running an older build on the UCUN chip needs one flash with M-Flasher or m-bootloader before the usual installer works.

The amp is muted before the splash draws. The audio starts while the panel is still dark, so the start click lands in the boot window and the rose no longer pops.

ableton/FM-1/ is a Control Surface script for Live 12. KNOB 1 to 4 of each FM-1 track controls one page of four parameters on the selected device. ALGORITHM chooses the page. Install steps and the ROUT CH1-4 requirement are in ableton/README.md.

3.7

KNOB 1-4 send a relative MIDI CC on the USB output while a computer is connected, one CC per detent, without changing what the knob does on the FM-1. The bank is the selected track: CC 16-19 on track 1, 20-23 on track 2, 24-27 on track 3 and 28-31 on track 4, value 64 + detents (Bin Offset), on the track's MIDI channel, the same one its keys use. ALGORITHM selects the track, so it selects the bank. A fast turn carries the panel's knob acceleration (x2..x16), so a flick crosses a DAW parameter as quickly as the FM-1's own. PRESETS is pitch bend and SELECT the mod wheel (CC 1) on the same channel, beside their local jobs (browsing sounds, stepping pages); a track change puts the old channel's bend back to centre and its mod to 0. Nothing is sent before the host enumerates the device. The package is assembled from three pinned SDK files in build/deps/ac79 instead of a full AC79 checkout; the firmware image and the package are unchanged by that. Splash and ABOUT show v3.7.

No project or settings change: saves stay FUN19 (FUNJ), and projects, presets and settings from 3.6 load as they are. On the device nothing changes except the extra CCs on the USB MIDI output; with no host attached the output is as before. A DAW that records MIDI from the FM-1 (Track enabled) will record those CCs into a clip.

  • Knobs out. KNOB 1-4 send CC 16..31 as above. The knob still edits its page, layer or menu value: the CC is sent beside the local action, so navigating pages does not change which CC a knob sends.
  • Acceleration. The CC follows the panel's curve (ui_input.c accel): ACC_RATE / ms per detent, doubled above 17, up to x16, with the first detents of a turn and a reversal at one step. Its timing is separate, so sending CC never changes how the page knob accelerates.
  • Pitch and mod. PRESETS sends pitch bend (14-bit, centre 8192, 1/64 of the range a detent) and SELECT sends the mod wheel (CC 1, 0..127). Both persist and both keep their local jobs. A track change sends the old channel's bend back to centre and its mod to 0.
  • Relative only. The value is 64 + detents, clamped in 63-step chunks. In Live, map the knob and set the mapping to Bin Offset if the automatic detection guesses another relative mode; Live's manual suggests turning the knob slowly left while assigning.
  • No collision. 16..31 are not used by anything else the firmware sends; notes and clock are untouched.

3.6

FM6's E5 macro is VIB now, the patch LFO's pitch depth, instead of VMOD. Old projects and user presets move their VMOD value into the modulator operators' velocity sensitivity, so their sound and velocity response stay the same; their E5 automation is dropped. The DIGITAL engine's DSP and its conversion are gone, and project formats FUN1..FUN6 (0.x .. 1.0 development) are no longer read. MRAT moves the modulators' ratios on a sounding note, so a matrix slot on it works. ANALOG's INT greys out on SUPER; SEQ's DETAIL / AUTOMATION open the EDIT page and AUTOMATION's OCT- deletes a row; the matrix gains VEL and its CHRD / VOIC slots reach the chord keys. No project format change: saves stay FUN19 (FUNJ); header bit 2 marks the VIB meaning. The boot splash's rose is drawn in code now, the same mark without its 2 KB bitmap. Splash and ABOUT show v3.6.

  • DIGITAL sounds no longer convert. Engine 1 keeps its reserved index as a silent stub; a project or user preset whose sound was DIGITAL does not play (projects load the track silent, a DIGITAL user preset is refused). Convert such files in the web editor before uploading if their sound matters.
  • FUN1..FUN6 projects are refused. Projects of Felucca 0.x and the 1.0 development builds (before FUN7) show as EMPTY, as a format this firmware does not know. Re-save them from an older build or the web editor. FUN7..FUN19 are unchanged, and new saves stay FUN19 (FUNJ).
  • The web editor converts on upload. DIGITAL sounds (library files) and old project files are converted client-side before they are sent: FUN1..FUN6 to FUN19, and DIGITAL tracks to FM6. No firmware code needed.
  • VIB. EDIT 2 KNOB 2 changes the patch LFO's pitch depth, not the track LFO. It is also an LFO / matrix destination and a lockable parameter under EDIT.
  • Old VMOD. A project or user preset from before 3.6 has VMOD in E5. On load, the value is added to the modulator operators' velocity sensitivity in the stored FM6 patch and E5 is cleared. VMOD automation has no patch target, so those E5 events go.
  • MRAT in the matrix. MRAT (E4) moves the modulators' ratios on a sounding note now; before, it was baked into the operators at note-on, so a MOD slot pointed at it did nothing. No sound change with the macro at rest (the same coarse offsets, applied per block).
  • CHRD / VOIC in the matrix. The chord keys read the matrix value as a key starts, so a slot on CHRD (chord type) or VOIC (voicing) changes what the key plays; before, the block's value was never read.
  • Every destination tested. mod_test renders one child per destination with a slot on it, in a rig where each can reach the output, and fails if the sound is unchanged: the bug class behind MRAT. master_test does the same for GLO > MASTER's CLIP / PNCH / DUCK / DREL.
  • CLIP. The knob now lowers the clipper's ceiling (32000 down to 6000) instead of driving a fixed one, so an ordinary mix audibly clips instead of passing almost unchanged; the makeup restores the ceiling's level and adds up to +1.5 dB. CLIP 0 stays bit-identical (bypass).
  • PNCH on every kit. The punch curve (x1.46 attack, x1.70 body into the knee, the tail cut) now applies to the kick of DRUMS and SAMPLE kits (CR78, USR drumkits) as well as DRUM-X, which keeps punching every lane. It is still per hit, by the hit's own age.
  • DUCK on every kit. A kick from any kit's track (DRUM-X all lanes, DRUMS and SAMPLE kits' kick) triggers the sidechain; a kit track is never ducked by its own kick.
  • Engine and conversion removed. eng_digital.c, the FELUCCA_FM4 build flag and its UI / test variants are gone, and fm4_convert.c follows them: engine index 1 is a silent stub. Old DIGITAL projects load with that track silent; DIGITAL user presets are refused (see Compatibility).
  • Splash mark in code. The boot rose and its dotted polar grid are drawn from the sine table now; the 2 KB bitmap, ten never-drawn keycaps and the hidden DIGITAL OP pages are gone.
  • OSC B INT on SUPER. SUPER has no second oscillator, so INT does nothing there; its card is drawn DIM and keeps its value, as WAVE and MORPH are under SYNC / SUB / SUPER.
  • EDIT no longer resets or deletes. On DETAIL and AUTOMATION the EDIT button opens the EDIT page, as on the other pages: a step's CHANCE / RATCH / NUDGE / VEL and an automation record stay. OCT- deletes the selected row there (SAVE held undoes it), as does the web editor's MOTION delete.
  • VEL destination. A matrix slot can scale a note's velocity at note-on, a gain like AMP: LFO -> VEL thins the notes out at the bottom of the cycle, VEL -> VEL -64 closes a full-velocity note. The sources are taken as they are at note-on, and the VEL source reads the scaled value after. Appended as DST 51.

3.5

ANALOG gets OSC A / OSC B pages: OSC B's own wave on every filter TYPE, PWM and its MORPH, DRIFT, and the filter TYPE on page 3. A strummed chord records into one step in free take too; ENV DEST's fourth card reads SYNC and TAPE's WOW reads FLUTR; SAVE > CLEAR clears FX and HELP is retired. CLOUD's SIZE 127 is a true freeze that holds the tail instead of droning. No project format change: saves stay FUN19 (FUNJ). Splash and ABOUT show v3.5.

  • OSC A / OSC B pages. OSC A: WAVE, MORPH (the wave slides toward the next plain one; PWM widens toward 54 %), DRIFT (each voice's slow pitch / filter wander), NOISE. OSC B: its own WAVE (SAME by default, following OSC A), INT (interval from OSC A, -24..+24 semitones), DTN, MIX; it works through LP, BP, HP and COMB, and is greyed only in SYNC / SUB / SUPER, which define OSC B themselves. EDIT > FILTER is page 3 now, its KNOB 4 DRIVE; the KTR knob is gone (keytracking fixed at its old default).
  • Compatibility. E8 is INT now. Older projects and user presets load it as 0, with MORPH / DRIFT 0, and drop their E8 / OP automation, with OSC B's wave on OSC A's; project header byte 67 bit 1 and the user preset category byte's bit 7 mark the new meaning, so no format version changed.
  • Free take + STRUM. A strummed chord records into the first string's step, as step recording does, so the take plays the chord together instead of one string per step. A fine strum no longer forces a 1/32 grid.
  • CLOUD FREEZE holds the tail instead of droning. At SIZE 127 the line stops taking input and its buffer is held; the last grain swarm keeps reading it with fixed windows, so no new grains are born and the texture no longer mutates. The room return is DC-blocked on the freeze path too, so the hold stays centred instead of settling into the old sub-audio drone. The last second stays level-stable at high DAMP as well.
  • ENV SYNC and TAPE. ENV DEST's fourth card is SYNC (was ESYNC) and draws LFO 2's tempo icon; TAPE's WOW card is FLUTR. Library files keep the ESYNC key, so files written before 3.5 still load.
  • SAVE > CLEAR clears FX. B3 clears the selected track's inserts, order, sends and slicer; F4 clears every track's plus MASTER, the SEND knobs and the global FX. The ALL / ALL4 actions clear FX too and move to the black keys F#3 / G#3; the white cells there are FX / FXS now.
  • MENU > SYSTEM > HELP is gone. The hint row under the keys and its HELP setting are retired; the editor's id 24 stays reserved. SYSTEM keeps USB SERIAL, RESTORE LAST, HARDWARE CALIBRATION, INFO and ABOUT.

3.4

The LFO pages' waveform comes alive: it draws from the running LFO and scrolls at RATE (or SYNC), and S&H's SMTH is drawn as a smooth glide from hard steps at 0% to a rounded random wave at 100%. CLOUD's reverb tail now ends in silence instead of leaving a sub-audio drone, and SIZE 127 is an explicit FREEZE that holds the tail. No project format change: saves stay FUN19 (FUNJ). Splash and ABOUT show v3.4.

  • Live LFO graphs. The LFO page's wave draws from the part's live phase and scrolls left at RATE (LFO 2: at SYNC's note value) instead of sitting at PHS. SIN / TRI / SAW / SQR show two cycles; S&H scrolls its steps.
  • SMTH is drawn. S&H's SMTH (LFO 2's KNOB 4) blends the graph from hard steps at 0% to a smooth, spline-like random wave at 100%, with rounded turns. The graph keeps the last three step values (a few bytes) so the older cycle in its two-cycle view, and a wrap, stay continuous.
  • CLOUD's tail ends. The room → granular return was floored and had no DC block; ROOM's comb gain at 1–5 Hz and the grain bank's overlap gain pushed that loop to unity, so an impulse of any level grew into the same ~15k RMS offset that played for ever after the music stopped. The loop now rounds towards zero and high-passes the room return, and the tail reaches exact silence at every SIZE below 127.
  • CLOUD FREEZE at SIZE 127. The top SIZE holds the tail instead of treating it as a heavier decay: the line recirculates with no new input. The graph shows FREEZE over the last normal grain pattern.

3.3

Safer audio maths, the LEDs dark during a flash erase, MAP ALL sharing one scale across every track, and the AUTO / MELO chord keys, with a strummed chord recorded as one step. No project format change: saves stay FUN19 (FUNJ); an old ALL loads as CURR and an old CURR / SCALE LOCK loads as ALL. Splash and ABOUT show v3.3.

  • LEDs dark during a flash erase. The erase stops the LED scan for ~17 ms, which left one column lit; the rows are switched off first (#236). Ported from Felucca 1.6.
  • Safer audio maths (#265). Left shifts of negative audio values (undefined in C) are multiplies, wrapping multiplies run in unsigned, and signed phase additions wrap in unsigned; the output is bit for bit the same (golden hashes unchanged, binary identical). From Felucca (f9a98fc, Mario Faúndez Vidal) and Felucca-Engines (e88bc70, 7511c0a). New strict-UBSan tests for the DC blocker, low-cut, FM6 phase and PHYS.
  • MAP ALL is the shared scale. ALL now sets MAP, ROOT and SCALE on every track while it is on, quantises every track's keys and sequence, and puts each track's own MAP / ROOT / SCALE back when you leave ALL. CURR is the per-track mode: it quantises the current track's keys and sequence and shares nothing. KBD and SEQ keep their meanings. Old projects keep their behaviour: an old ALL loads as CURR, and an old CURR / SCALE LOCK loads as ALL.
  • AUTO chord keys. CHRD gains AUTO, before MELO. The key picks a 3- or 4-note chord in the selected scale. It follows the other tracks' recent notes (their last two unharmonized onsets, arp-held keys and sequenced notes) and moves smoothly from the previous chord. A two-beat pause, STOP, or a scale / root / map / voicing change starts a fresh phrase. AUTO keeps 20 bytes of history per track, packed so the pool gate stays green. Ported from Melodee (f4fdbc7, Kerem Kilic, GPL-3.0-only).
  • A strummed chord records as one chord. With REC armed, the strings of one strum now go into the first string's step instead of one string per step, so the pattern plays the chord back.
  • MELO chord keys. CHRD gains MELO, after POW, the former AUTO2 name. The key you press is the melody and always the top note; the chord below it uses only notes of the selected scale, and VOIC moves the lower voices only. A DOWN strum sounds the melody first. MONO / LEGATO / UNISON play the melody alone; kits still ignore CHRD. No project format change: older firmware clamps MELO to POW. Ported from Melodee (f4fdbc7, Kerem Kilic, GPL-3.0-only).

3.2

The stock V15 supply rails before core 1, Felucca's DRUMS engine, a per-step PITCH lock, beat-synced chord STRUM / STROKE, the new REPEAT 1/12, /2 and *2 TEMPO and GLITCH punch-ins, the DELAY page's TIME / RATE direction swapped, TAPE as the tenth EFFECTS bus, and MASTER on every EFFECTS row. New saves are FUN19 (FUNJ); FUN18 and older load with TEMPO ON. FUN17 and older have no MASTER owners; FUN16 and older load with TAPE off and the EFFECTS order rebuilt. Splash and ABOUT show v3.2.

  • Stock V15 supply rails. Before the guards, core 1 and the audio start, the FM-1 is set to the stock V15 rails (VDC14 1.60 V, SYSVDD 1.38 V, VDDIO 3.2 V) with the stock write order, then read back. A timeout or a wrong value stops the sequence and keeps one core. MENU > ABOUT shows RAILS 7/15 (3/11) (after, and what the boot loader left) or RAILS FAIL 1 CORE. Ported from Melodee (hal/fm1_power.h); the P33 driver stays Araminta's. tests/power_test.c replays the V15 transaction trace, every timeout and the read-back faults.
  • MASTER on every EFFECTS row. USE AS now goes CHAIN / SEND / MASTER for the six inserts and the common DLY / REV / SLCR / TAPE buses. A master stage runs on the whole stereo mix, in the EFFECTS order of the track that selected it; that track shows MASTER and the others show USED on the shared buses. Inserts keep their per-track CHAIN / SEND beside a private MASTER instance (2x state, in the POOL); the shared buses are exclusive, since a second delay line / third reverb tank would not fit. MASTER inserts use the owner track's parameters and MIX; shared masters use the owner track's DLY / REV / SLCR MIX. The routing saves in FUN19.
  • TAPE TEMPO (K4). The TAPE page's fourth knob is TEMPO, OFF / ON, default ON. ON keeps the transport, voices and sequencer in time and makes SPEED the rotating head's pitch only; CHAIN and MASTER then mix the head in by MIX (a wet amount, like SEND) and at SPEED 100 with no WOW / DROPOUT the head is bypassed. OFF is the source-clock varispeed: CHAIN / MASTER move the transport and voices with SPEED. SEND always keeps time, so its TEMPO card is dimmed and fixed ON. Saves in FUN19; FUN18 and older load ON, and older FUN19 saves keep their bit (ON now means keep-time). The TAPE page draws an OP-1-style transport: two large reels with a ribbon and guides; SPEED turns the reels, WOW rocks them and the ribbon, DROPOUT sags it.
  • TAPE SPEED / WOW in LFO MOD and step locks. Both are MOD destinations (TSPEED / TWOW after the existing DLY / REV targets) and lock targets from the TAPE page (KNOB 1 / 2 on a held SEQ step). As with other shared sends, CHAIN allows only the owner track and MASTER allows every track; SEND is claimed by the first track that uses it. The matrix's per-part values and step locks take effect on the next audio block.
  • DELAY K4: left TIME, right RATE. Turning knob 4 left selects free milliseconds, turning it right the note divisions; the mode column shows TIME or RATE. The division last used is still the one TIME returns to. This swaps the 3.0–3.1 direction, so it is a change of muscle memory, not of stored data (G_DTIME is unchanged and old projects load the same).
  • RATE tap through a tempo change. With TAPE MASTER or TEMPO OFF the RATE tap's target follows the tape speed every block. The tap now holds while the target moves, then fades out, moves and fades back in (~12 ms), so the feedback loop keeps its pitch instead of splicing (crackle) or gliding (detuned grain). Division changes still snap; free-ms TIME still glides.
  • REPEAT 1/12 (PUNCH-IN 1/2, G3). A third of a beat (the 8T rate), on the same 1/16 start as the other REPEATs. It is a buffer effect like 1/8: below ~54 BPM the loop is too short and the cell dims.
  • /2 and *2 TEMPO (PUNCH-IN 2/2, A4 and B4). /2 is the former 1/2 TEMPO, now beside its double. While held, every target track's sequencer runs at half / double speed; let go and it lands where it would have been. /2 + *2 cancel. Recorded in the punch-in lane as nibble 11 (older firmware ignores it); /2 is nibble 3.
  • GLITCH (PUNCH-IN 2/2, C5). The master is cut on the transport's 1/16s. A deterministic hash of each slice's place in a 2-bar cycle decides: play live, repeat the last L, reverse the last 1/16, an octave up or down, gate, SKIP, or CRUSH; every slice is windowed. Knobs are fixed (DENS 50 / PITCH 0 / SIZE 0 / VARI 1). It borrows the SLICER's buffer, like REPEAT / REVERSE / TAPE / FREEZE; below ~82 BPM only gates, crushes and live slices play. Ported from JIANT 0.9.9-snd2 / 0.9.18. GLITCH is audio-only and never recorded.
  • The punch-in maps reordered. PUNCH-IN 1/2: REPEAT 1/8 / 1/12 / 1/16 / 1/32, LPF, HPF, OCT-, OCT+, DEC-, DEC+, ST8, ST16, ATK+, ARP, RND, none. PUNCH-IN 2/2: REVERSE, TAPE, FREEZE, PITCH+, PITCH-, FLANGER, PHASER, REV THROW, ECHO THROW, /2, *2, GLITCH, then none; G5 is still CLR with FX LATCH. The FX map's cells show GLITCH, /2 and *2.
  • FILTER COMB knee and DELAY FDBK bars. Insert FILTER COMB gets a soft knee at half scale, threshold 32000 after the voices are summed, so a chord is not compressed hard. The DELAY page's FDBK bars now follow the real loop gain (FDBK * 230 / 32768) instead of clamping above 100.
  • TAPE, the tenth EFFECTS bus. SPEED (25..400 %), WOW (slow + flutter) and DROPOUT (short pitch fluctuations, not level dips). USE AS is CHAIN / SEND / MASTER: MASTER and CHAIN slow the source (the transport and every voice's pitch); SEND keeps the dry at tempo and adds the head's pitched copy. MIX is one global amount, the same on every track and kept when switching route; in MASTER / CHAIN it is the depth (0 normal, 127 the full SPEED change), in SEND the send amount. The TAPE page opens from EFFECTS like DELAY / REVERB (SPEED WOW DROP); MIX stays on the EFFECTS list.
  • TAPE's clock and head. SPEED scales beat_samples() for MASTER and the owner track's sequencer for CHAIN, plus a pitch offset in 1/16 semitones (a 376-entry log table, 192 * log2(pct / 100)) through the voice pitch. Notes and the beat stretch together; envelopes and the reverb decay stay in real time, the delay divisions and the click follow the transport, and CHAIN leaves the other tracks alone. The SEND head is a two-head crossfaded delay line at 44.1 kHz; its rest delay and the SEND dry compensation are 512 samples (11.6 ms). The wrapping head has weight zero at the wrap, so the old click is gone. At 100 % with MIX 0 the list is bit-identical and the golden renders are unchanged.
  • TAPE storage. The dead global ids G_DMIX, G_MIDI, G_INFO, G_CLRSEQ, G_INITSND are TAPE SPEED, WOW, DROP, the one MIX and the route; P_TAPEMIX (the old GLMOD id) is unused. The 8 KB + 4 KB head and compensation lines live in the POOL.
  • DRUMS: Felucca's drum engine is back. A separate engine (15) beside DRUM-X, with the original synthesized 8-lane kits: STD, 80, 10, 66, 55, 77, DEEP, TIGHT and PERC. Parameters KIT / TUNE / TONE / DECY / SNAP / ACC / KICK / DRV, the GM key map, lane mutes and the SEQ drum grid. DRUM-X stays engine 10; old projects and presets still play DRUM-X. Flash +14,384 B, RAM +208 B, POOL unchanged. Favorites for engine 15 are skipped because the 16-row table is full. Editor protocol engine 15 and the web editor table are updated.
  • GENERATION on every drum kit. The SEQ GENERATION section is no longer DRUM-X-only: DRUMS, the CR78 SAMPLE set and a USR slot tagged Drumkit show it too. It writes the same KICK / SNARE / HAT lanes and keeps the same MAP / density / CHAOS controls and SAVE undo.
  • FUN19 (FUNJ). Same layout and 3840-byte size as FUN16/17/18. Each track's ten-slot EFFECTS order rides in the unused high bits of its FM6 patch bytes (after the six generation controls); each stage's MASTER owner (3 bits) goes in the chain header's spare bytes 1..3 and the motion header's spare byte 3; TAPE TEMPO is header byte 67 bit 7. FUN18 and older load with TEMPO ON; FUN17 and older have no MASTER owners; FUN16 and older rebuild the order from P_IORD / P_CHOR / the SLCR slot and load with TAPE off. Only FUN19 is written. Firmware that only knows FUN16/17/18 refuses a FUN19 (magic): its slot shows EMPTY until saved over, so keep a backup before the first save. The editor reads the order through PROJECT / TRACK_DUMP as before; no command changed.
  • SCALE LOCK is now MAP = CURR. The CHORD page's third knob is gone; MAP on SCL page 1 is OFF / ALL / CURR / KBD / SEQ (CURR is stored as 4, shown third). CURR quantises keys and steps exactly like ALL and shares ROOT / SCALE across every CURR track: entering pushes them, ROOT / SCALE edits follow, leaving restores the track's stash. MAP itself is each track's own, which the old link could not do.
  • Compatibility. CURR saves as MAP = ALL plus the lock bit, so v3.1 opens a v3.2 project as SCALE LOCK + ALL, which sounds the same. A v3.1 project locked with MAP OFF / KBD / SEQ loads with that MAP and unlinked (the notes are unchanged; only future linking is lost). New tracks default to MAP OFF and are unlinked. The stored layout is unchanged.
  • Free take: a strummed chord keeps its sweep. The strings are re-spaced to the STRUM division (1/8, 1/16, ...) at the take's closing tempo instead of the tempo the project had before the take. A chord strummed at 1/8 while playing a slower loop therefore still sounds as 1/8, and its strings no longer receive the legato SF_SLIDE or the mono return (a strum is a chord, not a tap). A 1/16 strum needs two steps, so a 1- or 2-bar take that recorded one closes at 1/32 (LEN 32 / 64) instead of 1/16; a 4-bar take has only 64 steps and stays 1/16. tests/freetake_test.c covers a 1/8 strum played at 80 BPM with the project at 120, and a 1/16 strum on 1- and 2-bar takes.
  • NOTE EDITS on SEQ TOOLS. Stored-note edits, one undo each like COOK/RANDOM. On a melodic track the six edits follow the sequence tools with no gap: OCT− / OCT+ on E4 / F4 transpose the written notes ±12 (ties, rests and the notes past LEN stay); HALF on G4 stretches the pattern over twice the steps (LEN ×2, ties keep holding); \*2 on A4 squeezes each pair into one (LEN ÷2, the first playing step wins); HUMAN on B4 writes fresh velocity ±16 and nudge ±2 into every note step and switches QUANTIZE off so the nudge plays; DUP on C5 copies steps 1..LEN after themselves (LEN ×2, up to 64; locks and automation copy). On a DRUM track BEAT / MUTE and the lane tools keep E4..C5, so HALF / \*2 / HUMAN / DUP are D5..G5. OCT− on the page puts back every edit of the visit, including QUANTIZE.
  • STRUM and STROKE (SCL > CHORD K3 / K4). A chord key or a MIDI-in chord sweeps from its lowest to its highest note over the chosen division (OFF, 1/8, 1/16, 1/32, 1/64, 1/128, 16T, 32T); DOWN / UP / ALT set the direction, ALT flips per chord and track. Rate and direction freeze at the press, the timing follows a tempo change, and a release cancels the strings that have not played. Off with ARP on, MONO / LEGATO (their chord is the root), and a one-note chord. The knobs share the inert ALLOC parameter (packed); legacy ROT/REUSE values 0/1 remain OFF, and new sweeps use values 2..22. The stored layout is unchanged. The editor shows the packed list as SWEEP. Strum settings saved with earlier unreleased 3.2 builds need resetting after this encoding correction.
  • Per-step PITCH lock (SCL K4 on a held step). A new lock-only motion id, 127: an absolute chromatic transpose (-24..+24) that replaces the track's TRN on that step, one value for the whole step (a chord uses its first stored note, lowest for a keyed chord, when TRN records it). It counts toward the 88 on-disk records and the save-limit warning. Downgrade: firmware before 3.2 refuses a project whose motion holds id 127 (EMPTY SLOT), so save a backup before opening a v3.2 project with pitch locks on an older build.
  • Recording TRN writes that lock. With REC armed on the selected track while playing, turning SCL TRN stores the scale-fitted semitone result as the current step's PITCH lock (C4 +1 in C major stays C4), never a P_TRANS automation event; the TRN knob still moves (other steps without a lock follow it), and this step uses the fitted value. Editing that PITCH row changes its semitone value and it stays a lock (C4 +1 then plays C#4; off-scale is allowed). With REC off, TRN is the ordinary global transpose.
  • Kits ignore PITCH. On a DRUM or other key-mapped engine, SCL K4 and MOTION op 5 refuse to create a PITCH lock (rc 1), and a stored kit PITCH lock is inert: note events and lane hits play as stored, as TRN already does. Existing projects still load; the lock can be deleted.
  • Motion capacity is the device's, not 64. The web editor reads the real motion pool from INFO 41 01 (192 since FUN16, 128 in 1.2) instead of rejecting anything but 64, uses MOTION op 8 for every record and its lock kind, and still works with 64-record firmware. A PITCH lock (id 127) now edits and deletes as a lock instead of being sent back as automation.
  • DUMP and SLOWN agree with the rest of the protocol. DUMP sends P_IORD as its 0..719 insert order, like GET / SET, TRACK_DUMP and CHANGED; the SEND flags stay on the device. G_SLOWN's descriptor is 0..15 (legacy 1..4 still accepted), so an editor cannot clamp a mask to 4.
  • Smaller CPU0 stacks, 13,824 B more sample pool. The main-loop stack is 12,288 B (was 24,320) and the interrupt stack 6,144 B (was 7,936), the sizes Melodee 1.5 audited on the same SDK. Araminta's static worst call paths are 5,652 B and 1,868 B (2.2x / 3.3x margin); CPU1 stays at 4,096 B. MENU > ABOUT is unchanged; the console's status now prints c0_stack_used user/super so a device run can confirm the high-water marks. docs/RAM_STACK_AUDIT_3.2.md has the evidence and the workload checklist.
  • S&H SMOOTH. LFO > LFO 2's fourth knob (SMTH, 0..100 %) rounds the WAVE S&H steps into a smooth, sine-like random curve. It shows only while WAVE is S&H; 0 is the hard steps, bit for bit. The matrix's S&H / SLEW sources are unchanged. It uses the long-inert PRIO parameter's id, so the stored layout is unchanged.

3.1

A public-domain CR-78 drum kit joins SAMPLE, and the web editor's Samples tab becomes one card per USR slot. Same project and settings format as 3.0; splash and ABOUT show v3.1.

  • CR78 factory kit. SAMPLE gains a public-domain CR-78 set at SET 8, after USR1..USR3 so their indices stay 5..7. Eight one-shots map to the SEQ drum lanes (36, 38, 39, 42, 46, 45, 37, 56) and show the drum grid; preset 5 selects it. Source: Oramics "Sampled" CR-78 (Boxed Ear), public domain.
  • Samples tab. One card per USR slot with Sample / Drumkit / Wavetable; Drumkit maps roots to exact lane notes, Wavetable takes a table file or a folder medley, and the editor-only name field is gone. The FM-1 still shows USR1..3.
  • WAVETABLE. OSC B's knob is LEVEL (B LEVEL in MOD / AUTOMATION); the EDIT graph draws B's own wave on OSC B and A, labelled OSC A, while RATIO is hot there.
  • Fix. CR78 lanes no longer fall back to the missing-sample sine: the kick, snare and hats play their real one-shots.

3.0

A fifteenth engine, WAVETABLE, brings two morphing wavetable oscillators and FM from B to every track, and the three user slots now hold complete wavetables made from a Serum .wav or a folder of single cycles. Install from the web installer (Chrome or Edge, USB). Try it first in the browser.

Same project format as 2.8 (FUN16 / FUNG). Settings move to PER5; older settings load and migrate. Splash and ABOUT show v3.0.

  • Two oscillators, one table each. A and B read a 16-frame table with a mip chain, frame-major, in XIP; A-POS / B-POS morph through the frames and the mip level is chosen per block and voice, so a high note reads a short, band-limited level. BASIC and SPECTRAL are factory tables (16 x 512 samples down to 8, 65,024 B for both) and eight presets ship with the engine: WT BASS, FM LEAD, GLASS FM, WT PAD, GROWL, DIGITAL, PLUCK, SWEEP.
  • FM and feedback. FDBK feeds A back into its own phase (up to 0.60 cycle) and B>A phase-modulates A (up to one cycle); LEVEL at 0 leaves B as a modulator only, and RATIO tunes B against A at 0.25, 0.5, 0.75, 1, 1.5, 2, 2.5, 3, 4, 5, 6, 8, 12 or 16. FLT moves A-POS and SHP moves B>A; there is no engine filter.
  • Pages. EDIT has OSC A (WAVE, POS, FDBK, B>A) and OSC B (WAVE, POS, LEVEL, RATIO); MOD DST, AUTOMATION and step locks name the two oscillators WAVE A / POSITION A / WAVE B / POSITION B. The EDIT graph draws A after feedback and FM on OSC A, B's own wave on OSC B, and A (labelled OSC A) while RATIO is the hot knob there, since RATIO changes A's FM and not B's wave.
  • Editor: engine 14 in the list (NENGINES 15), the eight parameters, both pages and the protocol are in web/EDITOR_PROTOCOL.md; engines.c lists it after DRUM.
  • One table per slot. USR1..USR3 share the SAMPLE engine's three user slots. A slot holds an FWT1 header at 0 and int16 PCM at +512, frame-major with a mip chain: 16 frames x 1024 samples by default (65,280 B), and any layout that fits 81,408 B is accepted (40 x 512 is 81,280 B). An empty, sample or invalid slot keeps the sine fallback.
  • Protocol. SMP_BEGIN / WRITE / END / ERASE / INFO handle either header type; END validates the header and the data CRC-32, SMP_INFO bit 5 marks a wavetable, and backup

CHANGELOG.md on GitHub ↗